2.Product Dimension

3.Accessory List

5.AssemblyProcedure

5.1 Assembly Preparation

● RD6006/RD6006W/RD6006Pdigital power supply*1, S400case*1,400W65Vswitch power supply*1, DC regulated power supply*1

● Tools, accessory (3 pin plug cable, multimeter, screw driver, test pencil...)

● Proper assembly environment

It is recommend to use a 400W 65V switch power supply as shown below.

5.2 Assembly step

Note:The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the assembly, please straighten it before assemble it.

①Check the accessories: check if the accessories of S400 are same as accessory list or accessory picture.

②Check RD6006: connect the power cables to the input terminal of RD6006, and then adjust input power supply to 12v/1A to power on RD6006, and set 5V/1A output on RD6006, turn on the output to see if the output is normal.

③Back board assembly: install the rocker switch,AC power socket and fan on the lower board.

④Connect the cables to Switch power supply: connect the brown cable to the (L) terminal, connect blue cable to the (N) terminal, connect yellow-green cable to the (〨) terminal, connect the black cable of the fan board and the output black cable to the (-V) terminals, connect the red cable of the fan board and the output red cable to the (+V) terminals.As shown below.Connect the output

⑤Install the switch power supply

Install the switch power supply on the lower board

⑥Install the board and connect the power cable (dangerous,non-professionals should not operate)

Install the board of temperature sensor extension cable and fan board on the back panel, use brown cable to connect therockerswitch and the live wire (L) of the switch power supply;then use the brown cable to connect therockerswitch and the live wire (L) of the AC power socket;Use the blue cable to connect the neutral wire (N) ofAC power socket and the neutral wire (N) of switch power supply;Use a yellow-green two-colorcableto connect the ground wire (E) ofAC power socket and the ground wire (〨) of switch power supply.Insert the cable of the fan to the fan board as shown below.

⑦Switch power supply test:

Check the wring again and power on the switch power supply, and use test pencil to check the power and insulation status. Then use multimeter to check if the 65V output is normal, then use screw driver to adjust the output of the switch power supply to 68V.

⑧Install RD6006, install the CR1220 battery (prepare yourself) and wifi board (if you order the wifi version), then insert the RD6006 in the right way

⑨Connect the rest cables: connect thegreenterminalto the input of RD6006 and insert the temperature sensor extension cable to the socket on the back of RD6006.

⑩Power on and test

Connect power cable and turn on the switch, the fan start to work.

(Note: Temperature-controlled fan, when the RD6006 is powered on below 40℃, it will work for 3 seconds and then stop, and it will run at low speed below 40℃-50℃, run at medium speed below 50℃-60℃, run at full speed when the temperature exceeds 60℃)

⑪Install the screws of the case

⑫Install the foot pads.

⑬If you want to use the temperature sensor, you just need to insert the cable on the back panel as shown below:

4.AccessoryPicture

5.AssemblyProcedure

5.1 Assembly Preparation

● RD6006 digital power supply*1,S12Dcase*1

● Tools, accessory(DC power supply,screw driver)

● Proper assembly environment

Note:The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the assembly, please straighten it before assemble it.

5.2 AssemblyStep

1. Check the accessories:

Check if the accessories ofS12Dare same as accessory list or accessory picture.

2. Install the female banana sockets and switch:

Please put the female banana sockets and rocker switch on the corresponding position of back board, the red female banana socket is positive electrode and the black female banana socket is negative electrode. Screw the fixing screws.

3. Connect cables

Use cables to connect switch and female banana sockets, and tighten with nuts, the wiring is completed, you can see the final connection below:

4. Install RD6006: install RD6006 on the front side and connect the external sensor.

5. Use 12V/1A DC power supply to power on RD6006, check if the connection succeeds(check the wring before power on)

6. Install the upper board: install the upper board on lower board, and use screws to fix it.