SUPER MB PRO M6+ PRO Truck Version for DOIP BENZ Wireless Diagnosis Tool with OBD2 16pin Cable + USB Cable + 14pin Cable Support BMW

Based on Super MB PRO M6+, the Super MB PRO M6+ Pro has greatly improved product functions and compatibility. It features real-time display of vehicle voltage and is 100% compatible with the original Mercedes-BENZ software.

Product Features

1. 100% compatible with the original Mercedes-BENZ software.
2. The front label of the M6+ Pro uses a design protected by trademark and art copyrights to enhance product recognition. It includes a multi-function switch button for one-click switching to BMW testing.
3. Communication between the M6+ Pro and the computer is via USB 3.0 or Ethernet cable, improving compatibility with both older and newer computers and tablets (no need to rely on devices with built-in network ports).
4. M6+ Pro supports remote C-side operation. The client does not need to install special diagnostic software—simply connect the M6+ Pro to a local internet-connected computer, and paid remote diagnosis and detection services can be provided. Customers can also set up local remote diagnostics within a LAN, significantly enhancing product flexibility.
5. M6+ Pro supports BMW E-SYS, Aicoder, and wired/wireless programming and coding for F and G series vehicles, including BMW modifications and hidden function activation.
6. M6+ Pro supports BMW mobile apps, including the English versions of Bimmercode (for coding and hidden function activation), Bimmerlink (for diagnostics and code clearing), and compatibility with MHD, Bimmergeeks, XHP Flashtool, ODIS-e, XDelete, THOR-the M Flasher, PRO-Tool, and other mobile applications.
7. M6+ Pro supports vehicles using the DOIP communication protocol, such as newer Volkswagen, Audi, Skoda, Bentley, and LaMBorghini models, and includes a dedicated transition button.
8. Supports new models including W223, C206, 213, and 167.

Product Functions

M6+ Pro, M6+, and M6 product function comparison chart:

M6+ Pro Connection Instructions

M6+ PRO Mercedes-Benz and BMW Configuration

1. Plug the M6+PRO into a power supply or connect the OBD to the test vehicle, and plug in the USB/LAN cable of the M6+PRO.
2. Turn on the computer and plug in the computer’s USB/LAN cable.
3. Open the computer’s network configuration interface and locate the “Realtek USB FE Family Controller” network adapter or the PC’s built-in network adapter.

4. Click “Properties” → TCP/IPv4, and set the IP address as shown in the figure below.

5. Click “Advanced”, and add a group of network IP addresses as shown in the figure below.

6. Click “OK”. After successful configuration, the display will appear as follows.

7. For the same computer, if you replace the M6+PRO unit, you must reset the IP address. Once configured, the computer is successfully bound to the M6+PRO, and no further IP setup is required for subsequent wired or wireless connections. (When using LAN port connection mode, IP reconfiguration is not needed when changing devices.)
8. You can now test Mercedes-Benz vehicles normally. Use the diagnostic cable with the SUPER MB PRO logo.
   
9. BMW Wireless BMWAiCode Configuration (F+G chassis only):
   Connect wirelessly to the M6+PRO -*** (password: 123456789). Press and hold the M6+PRO switch button for 3 seconds until the wireless indicator flashes. Configure BMWAiCoder on the computer as shown:
   
10. BMW Wired BMWAiCode Configuration (F+G chassis only):
    Connect the USB/LAN cable, press and hold the M6+PRO switch button for 3 seconds until the wired indicator light flashes. Configure BMWAiCoder on the computer as shown:
    
11. BMW Wired and Wireless E-Sys Configuration (F+G chassis only):
    For wireless: connect to M6+PRO -***, press and hold the switch button for 3 seconds until the wireless indicator flashes. On the computer, select direct connection as shown. Wired setup is similar and requires no additional configuration.
    
12. BMW Wired ISTA Configuration (F+G chassis only):
    Connect the USB cable, press and hold the M6+PRO switch button for 3 seconds until the wired indicator light flashes. Configure ISTA on the computer as follows:
13. BMW Wireless ISTA Configuration (F+G chassis only):
    Connect wirelessly to M6+PRO -***, press and hold the switch button for 3 seconds until the wireless indicator flashes. Select the following option on the computer side:
14. Mobile Phone BMW APP Wireless Connection (F+G chassis only):
    Connect to M6+PRO -*** (password: 123456789), press and hold the M6+PRO switch button for 3 seconds until the wireless indicator flashes.

Supported BMW Models and Years

Product Accessories Comparison Chart

SUPER MB PRO M6+PRO FULL

• 1pc x SUPER MB PRO M6+ Pro Host
• 1pc x OBD2 16pin Cable
• 1pc x USB Cable
• 1pc x 38PIN Cable
• 1pc x 14PIN Cable
• 1pc x 4PIN Cable

SUPER MB PRO M6+PRO OBD

• 1pc x SUPER MB PRO M6+ Pro Host
• 1pc x OBD2 16pin Cable
• 1pc x USB cable

SUPER MB PRO M6+PRO Truck

Package Includes

• 1pc x SUPER MB PRO M6+ Pro Host
• 1pc x OBD2 16pin Cable
• 1pc x USB cable
• 1pc x 14PIN Cable