PSA-COM BT Interface OBD2 Diagnostic&Programming For Citroen/Peugeot Replace of Lexia 3 PP2000 PSACOM PSA COM Code Reader

PSA-COM is a diagnostic program for Peugeot/Citroen vehicles. It can access to various electronic control units (ECUs) such as Engine, Gearbox, ABS, Airbag/SRS etc. and also can display identification, read and clear fault code memory, display and record measured values and perform actuator tests.

PSACOM BT PSA-COM BT Diagnostic program for Peugeot/Citroen

PSACOM BT is diagnostic tool for Peugeot/Citroen, dealer level diagnostic and programming advanced device, it is able to communicate with BT.

Multi-language Available: Arabic, Croatian, Czech, Danish, Dutch, English (United States), Finnish, French (Standard), German, Greek, Hebrew, Hungarian, Italian, Polish, Portuguese (Brazilian), Romanian, Russian, Serbian (Cyrillic), Spanish, Turkish

PSACOM BT PSA-COM Features:

Fully multiplexed all-in-one BT interface
Automatic ECU recognition
Automatic vehicle scan
ECU Identification : – finds all the available ECUs in the car by pressing the single button.
BT– wireless connectivity to your Windows laptop or tablet
Fault code (DTC) reading
Fault code clearing, with the ability to store DTC vehicle history forever

Freeze frame reading
Measured vaules / live data Live data recording, fully dynamic with graphing of up to 6 data streams at a time, recording and other manipulations
Diagnostic protocol printing

Actuator tests , test components via direct ECU access

Service reset
DPF (Diesel Particulate Filter) regeneration
EGR (Exhaust Gas Recirculation) self-test
Airbag programming
Injector programming
Power Steering calibration
ECU replacement
Car configurations

All 10 modes of OBDII test for a complete diagnosis via PSA COM :

Reading Codes:Show the detailed description of the Diagnostic Trouble Code (DTCs)

Erasing Codes & Reset:Turns off Check Engine Light (MIL), clears codes and resets monitors.

Data Stream:Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

I/M Readiness Status:Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

Read Live Data Stream:Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

View Freeze Frame Data:Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

O2 Sensor Test:Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

On-Board Monitor Test:Retrieves and displays test results for emission-related powertrain components and systems.

Read Vehicle Information:Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

Component Test:Certain vehicle components can be actuated by commands sent from the scanner to test their operability

for Renau-lt-COM BT is dealer level diagnostic and programming advanced device for Ren-ault vehicles. It can access to various electronic control units (ECUs) such as Engine, Gearbox, ABS, Airbag/SRS. It can perform these functions including display identification, read and clear fault code memory, display and record measured values and perform actuator tests

Notice：

1. same function with for R-enault can clip which is with the Golden clip or full chip but cheaper than them,this product canmake reprogramming.

2. with BT

New for Ren-ault-COM BT Diagnostic Tool For Ren-ault Vehicles

fro Rena-ult-COM BT is dealer level diagnostic and programming advanced device for Ren-ault vehicles. It can access to various electronic control units (ECUs) such as Engine, Gearbox, ABS, Airbag/SRS. It can display identification, read and clear fault code memory, display and record measured values and perform actuator tests.

for Rena-ult-COM Hardware:

Our OBD2 to Ren-ault-COM interface contains eight piceses of ISO9141 K-Line, one piece of ISO9141 L-Line, CAN-BUS and analog measurement circuits.

Operation System (OS): Re-nault-COM BT diagnostic interface is compatible with Windows 2000/XP

Multi-language Available:

Arabic, Croatian, Czech, Danish, Dutch, English (United States), Finnish, French (Standard), German, Greek, Hebrew, Hungarian, Italian, Polish, Portuguese (Brazilian),Romanian, Russian, Serbian (Cyrillic), Spanish,Turkish

For Ren-ault-COM Features:

Fully multiplexed all-in-one BT interface
Automatic ECU recognition
Automatic vehicle scan
ECU Identification: – finds all the available ECUs in the car by pressing the single button
BT– wireless connectivity to your Windows laptop or tablet
Fault code (DTC) reading
Fault code clearing, with the ability to store DTC vehicle history forever
Freeze frame reading
Measured values / live data Live data recording, fully dynamic with graphing of up to 6 data streams at a time, recording and other manipulations
Diagnostic protocol printing
Actuator tests, test components via direct ECU access

For Ren-ault-COM Special Functions - perform dealer level high-end programming/coding such as:

Key programming
Service reset
DPF (Diesel Particulate Filter) regeneration
EGR (Exhaust Gas Recirculation) self-test
Airbag programming
Injector programming
Power Steering calibration
ECU replacement
Car configurations

Package Includes:

1pc x New For Ren-ault-COM BT Diagnostic Tool for R-enault

Where is the OBD Interface？