CG FC200 ECU Programmer Full Version with MPC5XX Adapter for BOSCH MPC5xx Read/Write Data on Bench

FC200 Highlights

1. Bundle Deal with CG FC200 Full Version and MPC5XX Adapter

Includes CG FC200 Full Version with all licenses activated and the CG FC200-MPC5XX-P02-M230102 adapter, enabling MPC5X series cloning without opening the ECU cover.

Supports BOSCH MPC5xx platform mode ECUs: MED9.1, MED9.5, MED9.5.10, ME9.0, EDC16CP31, EDC16CP35, EDC16C2, EDC16C8.

2. Protect Original Car Parts

Over 98% of supported ECUs operate in BENCH mode and OBD mode—no need to open the cover or drill holes, preserving the original condition of vehicle components.

3. Intelligent Recognition

The “identification” function helps diagnose ECU communication status and wiring correctness. If the ECU is undamaged and wiring is correct, successful recognition allows reading of chip, hardware, and firmware information.

4. Module Clone

Supports ECU data reading/writing and module cloning without synchronization matching or online programming. Features data sub-regional burning and automatic verification for maximum chip and module protection.

5. ISN Read and Write

Enables ISN code acquisition from all BMW series engine control units (including Mini), facilitating key matching and anti-theft system maintenance.

6. VIN Modification

Resolves issues related to duplicate or mismatched VINs, simplifying vehicle maintenance and registration processes.

7. Data Processing

Supports engine control unit data analysis and modification for Audi, Seat, Skoda, and Volkswagen models.
Supports disabling the anti-theft system on Bosch MED/EDC17 series ECUs.
Supports TPROT off function for Bosch VAG MEDC17 series, BMW/Mini MEVD17/EDC17 series, and Hyundai/Kia EDC17/MED(G)17 series.

8. Broad ECU Compatibility

FC200 supports not only BMW ECUs but also over 3,000 additional ECU types, comparable to KTAG, Kess, and Dimsport devices.

9. Three Operating Modes

Operates in CAN-BUS, Bench Mode, and Boot Mode for flexible diagnostic and programming scenarios.

10. Multi-Language Support

Available in English, French, and Simplified Chinese. Traditional Chinese, Spanish, Polish, and Turkish require an additional fee.

11. Full Version with All Licenses Activated

Includes Denso and China Delphi licenses. Free online updates for one year; annual renewal fee is $200 after the first year.

12. MPC5XX Adapter for Non-Invasive Cloning

The CG FC200-MPC5XX-P02-M230102 adapter enables MPC5X series cloning without opening the ECU cover.
Supported ECU models: ME9.0, MED9.1, MED9.5.10, EDC16C2, EDC16CB, EDC16CP31, EDC16CP35. Additional models are continuously being added.

CG FC200 Latest Update Information

CG FC200 V1.2.9.3 Registered Version (2025.07.16)

New Features:

1. DTC-OFF Function – Fourth Batch:
   VAG: MED17.1, MED17.1.1, MED17.1.6, MED17.1.21, MED17.1.27,
   MED17.5, MED17.5.2, MED17.5.5, MED17.5.21, MED17.5.25,
   MED9.1, ME7.5.10, ME7.5.20, ME7.5.30
   MG1CS008, MG1CS001, MG1CS111, MG1CS002
   Mercedes: SIM271DE, SIM271KE
   PSA: MED17.4, MED17.4.2, MED17.4.4, MD1CS003
   Land Rover: EDC17CP42, EDC17CP55, MEDC17.9
   Porsche: SDI4, SDI6, SDI7, SDI8, SDI9, SDI21.x
   Volvo: EDC17CP22, EDC17CP48
   Honda: EDC17CP16
   BMW: EDC17CP45
   Iveco: EDC17CP52
   Jeep: EDC17CP27
   Fiat: EDC17CP52, ME17.3.0
   Renault: MD1CS006
   CNH: EDC17CV41
   MAN: EDC17CV42
   Alfa Romeo: MED17.3.3
2. Idle Speed Modification Function Added:
   Honda:
   37820-Rxx-Hxx SH7058
   37820-5xx-Bxx SH72543
   
   Hyundai-Kia:
   ME17.9.11, ME17.9.1, ME17.9.11.1,
   MEG17.9.12, MEG17.9.13, MED17.9.8, MEG17.9.8, MEG17.9.21,
   SIM2K_140, SIM2K_141, SIM2K_341
3. New ECU Models Added:
   JBC/JAC: LINCONTROL LEC4AF, LEC4AP
   BAIC/Dongfeng/Geely/Changan/Proton: BOSCH MG1UA008, UP8
   DFM-Future: AECS FC-34
   VAG: CONTINENTAL Simos8.6
   Dongfeng: MD1CC878
   Fukuda: MD1CS089
   Buick: ME17.U.6
   FAW/Jiangling Motors: MD1CE108
   BYD/Haima: M7.9.7, M7.9.7.1, ME7.9.71

Bug Fixes:

1. Optimized PFlash writing failure issue in Wuling Easy-U3.6.
2. Optimized read/write failures in parts of Wuling Easy-U2.5 and U2W.

CG FC200 Update V1.2.9.2 (June 18th, 2025)

1. New BMW Coolant Temperature Setting feature added.
2. DTC Off function now supports more vehicle models.
3. Added support for new ECU models.
4. "Three readiness monitors not ready" now supports more ECU types.
5. Added a toggle for the Checksum feature in Settings.
6. Expanded VIN Modification support to additional ECU types.

CG FC200 V1.2.9.1 (June 9th, 2025)

1. New ECU Models with DTC OFF Functions:
   BMW Bosch:
   (B48): MD1CP002, MD1CS001, MG1CS003, MG1CS201
   (N13/N20/N55/B38): MEVD17.2, MEVD17.2.3, MEVD17.2.4, MEVD17.2.5, MEVD17.2.6, MEVD17.2.8, MEVD17.2.9, MEVD17.2.G, MEVD17.2.H, MEVD17.2.K, MEVD17.2.P
   BMW Continental: MSD81, MSV90
   Ford-Bosch: MD1CS005
   Jaguar/Land Rover-Bosch: MED17.8.31, MED17.9.7, MED17.9.9
   Mercedes BENZ Bosch: EDC17CP57, MD1CP001, MG1CP002
   Volkswagen Bosch: EDC17CP54, EDC17CP74, EDC17C74, MD1CP004, MD1CP014, MD1CS004
2. New ECU Models Added:
   Wuling:
   CONTINENTAL Easy_U2.5 SPC564xx
   CONTINENTAL Easy_U2W SPC564xx (1.2.9.2 upgrade)
   CONTINENTAL Easy_U3.6 SPC564xx (1.2.9.2 upgrade)
   CONTINENTAL Easy_U3D/U3E SPC564xx (1.2.9.2 upgrade)
   Geely: CONTINENTAL Easy_U2 SPC564xx

CG FC200 V1.2.9.0 Registered Version (2025.05.24)

New Functions:

1. DTC OFF Function – First Batch:
   BMW BOSCH: EDC16C31, EDC16C35, EDC16CP35, EDC17C06, EDC17C41, EDC17C50, EDC17C56, EDC17CP02, EDC17CP09
   Mercedes DELPHI: CRD2.x, CRD3.x
   Mercedes BOSCH: EDC16C32, EDC16CP31, DCU17PC42, EDC17C66, EDC17CP01, EDC17CP10
   Volkswagen DELPHI: DCM6.2
   Volkswagen BOSCH: EDC16U1, EDC16U31, EDC16U34, EDC16CP34, EDC17C46, EDC17C54, EDC17C64, EDC17C74, EDC17CP04, EDC17CP14, EDC17U01, EDC17U05
   Volkswagen CONTINENTAL: PCR2.1, SIMOS8.1, SIMOS8.2, SIMOS8.3, SIMOS8.4, SIMOS8.5
   Hyundai/Kia Bosch: EDC16C39, EDC17C08, EDC17C53, EDC17C57, EDC17CP14
   Opel GM: E78, E80, E83, E98
   Opel BOSCH: EDC16C39, EDC17C11, EDC17C18, EDC17C19, EDC17C42, EDC17C59, EDC17C60, EDC17C84
   Mazda DENSO: R2xx, RFxx, SH1x
   PSA DELPHI: DCM 3.5, DCM 6.2A, DCM 7.1A
   PSA BOSCH: EDC16C34, EDC17C10, EDC17C60
   Renault BOSCH: EDC16C36, EDC17C11, DC17C42, EDC17C84
   Subaru DENSO: KS/DT
   Toyota BOSCH: EDC17C73, EDC17CP07
   Toyota DENSO: Diesel Gen3
   Land Rover BOSCH: EDC17CP11
   Fiat BOSCH: EDC16C39, EDC17C49, EDC17C69
   Ford DELPHI: DCM6.1
   Ford BOSCH: EDC17C70, EDC17CP05
   Honda BOSCH: EDC17_CP06
   Iveco BOSCH: EDC16C39, EDC17C49, EDC17C69
   Jeep BOSCH: EDC17C79
   CNH BOSCH: EDC17C49
2. Newly Added ECU Models:
   Buick: MT60.1 MC9S12XEP768
   Wuling: MT60.1 MC9S12XEP768
   Shacman: EDC17CV44
   Great Wall: M7.9.7, M7.9.7.1, ME7.9.71, MT20U2 MC9S12XET256
   ChangHe: MT20U2 MC9S12XET256
   HAWTAI MOTOR: ME7.8.8, M7
   HAFEI: ME7.8.8, M7, TR40
   DongFeng: EDC17C81
   FOTON: TR40

Bug Fixes:

1. Fixed VIN modification failure on some Volkswagen ME17.5.22/24/26.
2. Fixed partial SID209 password read failure.

CG FC200 V1.2.8.0 Update Information (2025.05.20)

New Functions:

1. “Three Items Not Ready” Function Expanded:
   BMW: MSV90, MEVD17.2.2, MEVD17.2.8, MEVD17.2.H
   Hyundai/Kia: SIM2K-240, SIM2K_341
2. Volkswagen DQ380/DQ381 TCU now includes “mileage repair” function.
3. New Hyundai/Kia ECU/TCU Models:
   SIM2K-250_ECU, SIM2K-250_TCU, SIM2K-260, SIM2K-140_ECU, SIM2K-140_TCU, SIM2K-141_ECU, SIM2K-141_TCU
4. Added read-write, “modify VIN,” and “three items not ready” functions for Xiali DFO JH30 module.
5. Added read-write, “VIN modification,” and “three items not ready” functions for SAIC Maxus DFO TR20 module.
6. Verification function added for: MD1CC878, DCM3.7AP

Bug Fixes:

1. Optimized “three items not ready” function for DCM7.1AP.
2. Fixed unsupported version prompt on some BOSCH TC17xx ECUs.
3. Fixed PFlash verification failure in CPEGP2.10.1.
4. Optimized verification function for DCM7.1AP.
5. Optimized verification function for GM E37/E78/E83.
6. Optimized verification function for PCR2.1.
7. Optimized verification function for 9HP.
8. Optimized verification function for MT80.

CG FC200 V1.2.7.0 Update Information (2025.04.30)

New Functions by ECU Manufacturer

BOSCH TC2xx Series

MD1CP001, MG1CS003, MD1CP002, MD1CS006, MG1CP002, MG1CS080, MD1CP004 SPC5777, MD1CP004_ TC298TP,
MD1CS004, MG1CS001, MG1CS002 SPC5777, MG1CS002_ TC298TP, MG1CS111, MD1CP014, MG1CS008_ TC298TP, MG1CS016,
MG1CS017, MG1CS018, MG1CS019, MG1CS032, MG1CS026, MG1CS024, MG1CS201, MD1CS001, MG1CA007

BOSCH TC17xx Series

EDC17U01, EDC17U05, ME17.5.20, MED17.1.61, EDC17CP74, ME17.7.8, EDC17CP06, EDC17CP16, DCU17PC42, EDC17CP58, MED17.6.9,
EDC17CP68, EDC17C61, EDC17C47, ME17.8.31, ME17.8.32, EDC17CP05_ TC1797, EDC17CP05 TC1796, ME17.8.3.3, ME17.8.33, ME17.8.5, M17.8.7

BOSCH MPC 5xx Series

MED9.1, ME9.0, EDC16CP31, EDC16CP35, EDC16U31, EDC16C2, EDC16C1, EDC16U31, ME9.1.1, MED9.1.1, MED9.1.2

BOSCH ST10xx Series

ME7.7.0、ME7.9.9、ME7.1.1、ME7.8.2、ME7.6.4

CONTINENTAL/Siemens ECUs

SIM271KE, SIM271DE, SDI7, SDI6.1, SIMOS8.4x, SID208, SID310, EMS3110, EMS2511, EMS24xx, GPEC3, GPEC2A, GPEC4, GPEC4LM, GPEC2

DENSO ECUs

MB279700-9500, MB279700-9811, MB279700-9801, MB279700-96xx, RF7x, RF8x, 33920-67P0, R2xx, Pxxx, S5xx, SHxx, 275700_7082, RA6, 4N14,
23740_5Sxxx_Gen2, 23740-5Sxxx_Gen2, 23740-3Nxxx_Gen1, Subaru SH72531, 112800 SH72531

GM ECUs

E38, E39, E39A, E78, E80, E83, E98, E84

Hyundai/Kia ECUs

SIM2K_240_ECU, SIM2K_241_ECU, SIM2K_240R_ECU

Mitsubishi ECUs

E6T6xxxx、E6TAxxxx

DELPHI ECUs

DCM3.7AP、DCM3.5

Marelli ECUs

8TDW

Additional New Functions

1. “Three Not Ready” Function Support:
   • Peugeot/Citroen: MED17.4.2 TC1767, MED17.4.2_ TC1797, MED17.4.4, MEV17.4, MEVD17.4.4, MEV17.4.2 TC1766, MEV17.4.2_ TC1767
   • Maserati: MED17.3.4, MED17.3.5
   • BENZ/Smart: ME7.7.0
   • BMW: ME17.2.1
2. CALID Modification Function: Added for ME17.8.8
3. Dongfanghong Tractor Repair: EDC17CV54 time repair
4. JMC Mileage Repair: EDC17C55
5. Volkswagen Support: Added MG1CA811

CG FC200 V1.2.6.0 Registered Version (2025.02.27)

New Functions

1. “Three Readiness Monitors Not Ready” Function:
   • DELPHI: MT22.1, ME22.1.1, MT22U
   • Jiangling/Foton/Great Wall: EDC17C81/EDC17C63/EDC17C53
   • Jaguar Land Rover: MED17.0.1, MED17.0, MED17.9.7, MED17.9.8, MED17.9.9, MED17.8.31, MED17.8.32
   • Fiat: ME17.3.0
2. New Checksum Support: MT20U, MT22U, MT20U2, MT22.1, MT22.1.1
3. CALID Code Modification: Added for M7, ME7.8.8
4. Wuling SIM2K-D51 Module: Supports verification, VIN modification, and “three readiness monitors not ready” functions
5. Wuling SCE60 Module: Added
6. Hyundai SIM2K-47 Module: Added
7. VIN Modification Function Added for:
   • Marelli ECU: 8GMK, 8GML, 9GC
   • Bosch ECU: ME7.4.5, M7.9.8
8. Newly Added ECUs:
   • Volkswagen: simos12.1
   • Hyundai Kia: MEDG17.9.8

Bug Fixes

1. Optimized read and write functions for ME17.9.23, ME17.9.21.1, and EDC17C69
2. Fixed issue with some DCM7.1AP units failing to read/write PFlash
3. Optimized “three readiness monitors not ready” function for Wuling SIM2K-51.4

FC200 V1.2.5.2 Registered Version (2025.01.18)

New Functions

1. Domestic Model ECUs with “Three Unready” Functions:
   • Silver Housing: ME17, ME17.8.8, MED17, MED17.8.10, MED17.8.2, MED17.8.21
   • Black Housing: ECU6.1, ME17, ME17.U.6, UP6
2. Hyundai Kia ECUs with “Three Unready” Functions: MEG17.9.12, MEG17.9.13, MEG17.9.2, MEG17.9.21, MEG17.9.8, ME17.9.1, ME17.9.11, ME17.9.11.1, ME17.9.21, ME17.9.21.1, MED17.9.30, MED17.9.8, EDC17CP14, ME17.9.8
3. Jinbei Lingdian ECU: LINCONTROL LEC4A, LINCONTROL STC-213 – supports VIN change and “three unready” functions
4. Volkswagen Skoda ME7.5.20: Added “three unready” and VIN change functions
5. Chery ME7.9.7: Added ExtFlash verification algorithm
6. New Bosch ECUs: UP6 TC1728, MED17.8.21, ME17.9.8
7. Huasong N20 Model: Added with VIN code change support
8. BOSCH VIN Change ECUs: MEG17.9.13, ME17.9.1, EDC17CP48, EDC17C69, EDC17C83, ME17.3.0, EDC17C10, EDC17C58, ME17.0.3, EDC17C70

Bug Fixes

1. Fixed VIN modification failure for ME17/ME17.U.6/ECU6.1
2. Optimized verification algorithm for M7/ME7.8.8/M7.9.7/SIM2K-51.4
3. Fixed minor bugs and optimized software performance

FC200 V1.2.5.1 Registered Version (2025.01.15)

New Functions

1. Wuling SIM2K-51.4: Added read/write, VIN modification, and “three unready” functions
2. Jinbei Lingdian TR40: Added read/write, VIN modification, and “three unready” functions
3. Volkswagen ECUs: MED17.1.6, MED17.1, MED17.5, MED17.5.1, MED17.5.2, ME17.5.22, MED17.1.10, MED17.5.20, MED17.5.25, MED17.5.5, EDC17CP14 – added “three unready” functions
4. BMW N20/N55/B38/N13 ECUs: MEVD17.2.5, MEVD17.2.4, MEVD17.2.9, MEVD17.2.P, MEVD17.2, MEVD17.2.6, MEVD17.2.G, MEVD17.2.K, MEVD17.2.3 – added “three unready” functions
5. Verification Function ECUs: ME7, ME7.8.8, ME7.9.7, ME7.9.71, M7.9.7, M7.9.7.1, ME7.5.20

Bug Fixes

1. Fixed PFlash write failure in some ME17.9.64 units
2. Fixed data backup failure for Honda Keihin KEIHIN series ECU
3. Fixed PFlash verification failure for Hyundai Kia CPGDSH2.26.1
4. Fixed VIN code change function for ME17.9.1, ME17.9.11, ME17.3.0, and EDC17C81
5. Fixed minor bugs and optimized software performance

FC200 V1.2.5.0 Registered Version (2025.01.06)

New Functions

1. GM ECU “Three Readiness Monitors Not Ready” Function: E37\E38\E39\E39A\E78\E80\E83\E84
2. MELCO (Mitsubishi) BENCH Mode ECUs:
   • MELCO E6T6xxxx MH8501F
   • MELCO E6TAxxxx MPC5746R
   • MELCO E6T85xxx MH8601 test
   • MELCO E6T8xxxx MH8115 test
   • MELCO E6T7xxxx MH8611 test
   • MELCO E6T86xxx MH8115 test
3. BOSCH BENCH Mode ECU/TCU:
   • MG1CS080 TC275TP test
   • INVCON2.3 TC1797
   • HV17.4.1 TC1797
4. Lovol Engine Duration Repair: For EDC17C63, EDC17CV54
5. GM E83 BOOT Mode: Added read/write function
6. Mercedes-BENZ SIM271DE: Added separate read/write for DFlash, PFlash, Maps, and ExtEEPROM
7. Volvo MB279700-96xx: Added “Unlock” function
8. Hyundai Kia CPEGP2.10.1 Boot Mode: Added “Read Password” function

Bug Fixes

• Optimized “Turn off anti-theft” function for EDC17C53, EDC17C63, and EDC17C81
• Optimized Porsche SDI10.x ECU wiring diagram
• Fixed read/write failure for Mercedes-Benz CRD3P.C0 and CRD3P.D1
• Fixed PFlash write failure for DCM2.5
• Fixed recognition issue for M7 (read/write still functional)
• Fixed VGS2-FDTC recognition failure after version update
• Optimized “Three readiness monitors not ready” process for M7.9.7, M7.9.7.1, ME7.9.7, ME7.9.7.1
• Fixed communication failure after writing data to Honda 37820 SH7058

FC200 ECU Programmer Powerful Functions

1. Original Parts Protection

FC200 supports OBD and platform mode for more than 98% of ECUs and EGS units—no need to open the shell or punch holes, preserving the vehicle’s original components.

2. Smart Identification

The “identification” function helps users diagnose ECU communication status and verify correct wiring.
If the ECU module is undamaged and communicating properly, successful identification allows reading of chip and firmware information.

3. Module Clone

Supports ECU/EGS read/write and module cloning with synchronization matching—no online programming required.
Flash data by area with automatic checks to maximize chip and module protection.

4. ISN Reading and Writing

Supports ISN code acquisition for all BMW series (including Mini) ECUs—ideal for all-keys-lost scenarios and anti-theft fault resolution.

5. VIN Writing

Resolves issues of duplicate or mismatched VINs, simplifying vehicle maintenance.

6. Data Processing

Supports data analysis and modification for 4th and 5th generation Audi/Seat/Skoda/Volkswagen ECUs.
Includes anti-theft disable for Bosch MED/EDC17 series ECUs.
Features TPROT off function for Bosch VAG MEDC17 series, BMW/Mini MEVD17/EDC17 series, and Hyundai/Kia EDC17/MED(G)17 series.

FC200 ECU Programmer Software Display

1. Interactive Software Interface

Structured by brand → model → engine/gearbox → ECU to help users quickly locate the correct operating directory.

2. Built-in Model Search Function

Enables ECU model and Bosch nuMBer search—bypassing hierarchical menus for faster access to the function interface.

3. ECU Search Example

For BMW MSV90 ECU: Select “BMW,” choose “ECU” as the search condition, enter “MSV90,” and click search to display matching ECU types.
Same procedure applies to Bosch ECUs.

4. Visualized Wiring Diagram

1:1 simulation with bright colors to prevent wiring errors.

FC200 ECU Programmer Hardware

FC200 Main Unit

1. Integrated polymer injection molding with custom internal circuit boards and national patent certification

2. Compact, portable design that shields against interference for reliable operation in varied environments

3. Three expansion ports (12V power, USB, DB15)—automatically diagnosed and identified. The DB15 port connects to adapter cables and OBD cable.

FC200 Adapters

1. Vehicle-grade harness with synthetic metal conductors rated for 100,000 continuous uses

2. Precise fit ensures seamless ECU-to-host connection for uninterrupted communication

3. Equipped with B-type, C-type, D-type, F-type, and G-type pin interfaces for broad ECU/EGS compatibility

OBD2 Cable

Designed primarily for BMW B48/B58 ECUs to read ISN via OBD without disassembly.
110cm length, synthetic material construction—high-temperature resistant, waterproof, corrosion-resistant, with anti-fall buckle for stable connection.

CG FC-200 Package Contents

• 1pc × CGDI FC200 Host
• 1pc × OBD Cable
• 1pc × Jumper
• 1pc × USB Cable
• 6pcs × G-type Adapter Cable
• 3pcs × F-type Adapter Cable
• 6pcs × E-type Adapter Cable
• 6pcs × D-type Adapter Cable
• 6pcs × C-type Adapter Cable
• 6pcs × B-type Adapter Cable
• 1pc × MPC5XX Adapter