VIDENT iMax4305 OPEL Full System Car Diagnostic Tool for VAUXHALL OPEL Rover Support Reset/OBDII Diagnostic/Service

VIDENT iMax4305 OPEL Full System Car Diagnostic Tool for VAUXHALL OPEL Rover

VIDENT iMax4305 OPEL is a professional full system car diagnostic tool designed specifically for VAUXHALL OPEL vehicles. It supports full ECU diagnosis for single vehicle brands and operates using test modes such as CANBUS, ISO9141, KWP2000, and J1850. Equipped with a TFT LCD display and dedicated diagnostic software, it enables technicians to accurately identify and resolve complex vehicle issues.

Key Features of VIDENT iMax4305 OPEL

• VAUXHALL OPEL Diagnosis for Single Brand (OBDII-16DLC)
• Read & Clear DTCs
• Read Live Data
• ECU Information
• Freeze Frame Data
• Oil Service Reset
• Electronic Parking Brake (EPB) System Maintenance
• Battery Replace Test (BRT)
• Diesel Particulate Filter (DPF) Regeneration Control
• Electronic Throttle Control System (ETC)
• Steering Angle Sensor (SAS) Calibration
• ABS Bleeding
• I/M Readiness Test
• Data Playback and Print
• Full Speed Upgrade via PC
• TFT LCD Display (320*240 resolution)
• Lifetime Free Software Updates
• Multilingual Support: English, French, German, Spanish, Italian, Dutch, Polish, Swedish, Portuguese, Russian, and more

Special Functions of VIDENT iMax4305 OPEL

Oil Service Reset

Service Lamp Reset:

1. If the service lamp is illuminated, service must be performed on the vehicle. After servicing, reset the driving mileage or time to turn off the service lamp and initiate a new service cycle.
2. Use VIDENT tools to reset the service lamp after changing engine oil or components that monitor oil life.

Electronic Parking Brake (EPB) System Maintenance

Brake Pad Replacement:

1. When the brake pad wear sensor line is triggered, a signal is sent to the onboard computer indicating replacement is needed. After replacing the brake pads, a reset must be performed; otherwise, the vehicle may trigger an alarm.
2. Reset is required in the following cases:
   • The brake pad and wear sensor are replaced.
   • The brake pad indicator lamp is on.
   • The brake pad sensor circuit was shorted and has been repaired.
   • The servo motor is replaced.

Battery Replace Test (BRT)

Battery Matching:

1. Use the diagnostic device to reset the vehicle’s battery monitoring unit, clear previous fault data related to low battery charge, and re-establish battery matching based on current battery parameters.
2. Battery matching is necessary when:
   • The main battery is replaced. This clears old charge deficiency data and prevents false readings that could disable auxiliary functions like automatic start/stop, one-touch sunroof, or power window auto operation.
   • The battery monitoring sensor is serviced. Re-matching ensures accurate detection of battery usage data and prevents incorrect instrument panel displays.

Diesel Particulate Filter (DPF) Regeneration Control System

DPF Regeneration:

1. DPF regeneration clears particulate matter (PM) from the filter through high-temperature combustion, fuel additives, or catalytic methods to maintain optimal trap performance.
2. Regeneration is required when:
   • The backpressure sensor is replaced.
   • The PM trap is removed or replaced.
   • The fuel additive injector is removed or replaced.
   • The catalytic oxidizer is removed or replaced.
   • The DPF regeneration MIL is on and maintenance has been completed.
   • The DPF regeneration control module is replaced.

Throttle Position Sensor (TPS) – Electronic Throttle Reset

Throttle Matching:

1. Use the diagnostic tool to initialize the throttle actuator, resetting the ECU’s learning values to initial status for precise control of intake air volume.
2. Throttle matching is required when:
   • The ECU is replaced and lacks stored throttle characteristics.
   • The ECU was disconnected and memory lost.
   • The throttle assembly is replaced.
   • The intake passage is removed or replaced, affecting idle control.
   • The throttle body is cleaned, altering airflow characteristics despite unchanged potentiometer settings.

Steering Angle Sensor (SAS) Calibration

Steering Angle Reset:

1. Resetting the steering angle involves establishing the vehicle’s straight-line position as a reference zero point, allowing the ECU to accurately calculate left and right steering angles.
2. Calibration is required after:
   • Replacing the steering angle sensor.
   • Replacing steering components (e.g., gearbox, column, tie rod, knuckle).
   • Performing four-wheel alignment.
   • Vehicle collision repair affecting chassis alignment.

ABS Bleeding

1. Perform ABS bleeding when air is present in the ABS system to restore proper brake sensitivity.
2. This function is required after replacing:
   • ABS computer
   • ABS pump
   • Brake master cylinder
   • Brake cylinder
   • Brake lines
   • Brake fluid

OBDII Functions – Compatible with All OBDII Vehicles

Note: The OBDII functions are not limited to VAUXHALL OPEL vehicles and support most OBDII/EOBD protocols including CAN, ISO9141, KWP2000, J1850 VPW, and J1850 PWM.

• Read Codes: Retrieve generic (P0, P2, P3, U0) and manufacturer-specific (P1, P3, U1) permanent and pending Diagnostic Trouble Codes.
• Erase Codes: Clear both generic and manufacturer-specific DTCs.
• Determine MIL: Turn off the Check Engine Light (MIL) after clearing codes and reset system monitors.
• Data Stream: View live PCM data stream with color graphing and fast refresh rates for enhanced diagnostics.
• Freeze Frame Data: Access a snapshot of vehicle conditions at the moment an emission-related fault occurred.
• I/M Readiness Test: Check the status of emissions systems to confirm readiness for inspection and maintenance testing.
• O2 Sensor Test: Retrieve and view results of the most recent O2 sensor tests from the vehicle’s onboard computer.
• Evap System Test: Initiate a leak test on the EVAP system. Always consult the vehicle’s service manual before starting the test.
• On-Board Monitoring: Review diagnostic monitoring results for specific components and systems.
• Vehicle Information: Display VIN, CVN, and other vehicle identification details.
• Comprehensive Help: Includes OBD parameters, mode explanations, DTC search, and additional support features.

Compatibility: Works with most European OBDII-compliant petrol vehicles from 2001 onwards and diesel vehicles from 2004 onwards.

Package Contents

• 1pc x VIDENT iMax4305 OPEL Main Unit
• 1pc x User Manual
• 1pc x USB Cable