V2021.09 BMW ICOM NEXT A + B + C Wi-Fi NEW GENERATION OF ICOM A2
Top 6 Reasons to get 2021.09 BMW ICOM NEXT Improved Functionality and Performance:
Top 6 Reasons to get 2021.09 BMW ICOM NEXT Improved Functionality and Performance:
- With Latest software 2021.09 software, no need activation, plug and play
- More Satble and better sold that ICOM A2+B+C
- With free BMW Engineer Software (INPA, NCS, WinKFP, E-Sys 3.32.1, Psdzdata 5.06.01), BMW FSC code generator and BMW AiCoder
- Supports new F, G and I series models, as well as Rolls Royce, MINI, BMW Motorcycle
- With Multi-VCI, ICOM NEXT can support D-CAN line, ENET line, ICOM, OPS/GT1 direct connection diagnosis
- View maintenance materials, circuit diagrams, etc
Share the same functionality as ICOM A2
ICOM NEXT A+B+C with WIFI is a redesign of ICOM A2+B+C
Backwards compatible to car adapters (ICOM B, C) and motorcycle adapters (ICOM D, E)
ICOM NEXT ABC Specifications:
1. Gbit workshop LAN, backwards compatible
2. Preparation for Gbit LAN on vehicle OBD(cars do not yet support this and interface not yet defined,ICOM Next hardware adaptation will be necessary for future Gbit car interface,will cause adaptation costs)
3. Faster start-up time and high throughput
4. Through high-performance, low-power ARM SoC
5. Improved handling
6. More flexible OBD cable
7. Lighted button for logs etc
8. Zeroization of data on tamper detection
9. Secure supply chain assurance
10. Key storage using physically un-clonable function
11, CRI Pass-Through DPA Patent Portfolio
12. Advanced cryptographic Services
BMW Software Compagible wirth ICOM Next A:
ISPI NEXT—BMW ISPI NEXT is latest generation after service tool for BMW, these brief instructions describe the basic functions of the AIR application (Aftersales Information Research) in Service. For the Diagnostic, it use IPSI (Rheingold) and ISPI Next for Coding Programming functions.
ISTA/D— Integrated Service Technical Application Diagnostic. ISTA/D is used to diagnose BMW all series and models from all systems.
ISTA/P— Integrated Service Technical Application/Programming. ISTA/P is used to process all coded, programmed and enable-dependent control modules in BMW Group vehicles.
Rheingold—Diagnostic and repair guide, including Diagrams and disassembly Figure
KSD—BMW KSD (Kaufmännische Service Daten, i.e. Commercial Service Data) is a collection of invaluable data for determining labor hours, inspection sheets and general service methods. There’s also information about wheels and rims for the various models.
EasyConnect— Used to Configure the Environment Parameter of Engineer Software for E series, can activate or release ICOM Port
IToolRadar— Used to recognize ICOM, activate or release ICOM Port
ETK— Accessories Catalog
EDIABAS Tool32— Engineer Software for E series, able to run directly
INPA— Engineer Software for E series, for diagnosis
NCS Expert Tool—- Engineer Software for E series, for coding
WinKFP—Engineer Software for E series, for programming
E-sys — Engineer Software for F series (available for programming and coding)
BMW Standard tool
Coding Database
Coding Tool
V2021.09 BMW ICOM ISTA/D 4.15 ISTA/P 3.65 500G Format HDD
ISTA-D 4.25.4
SDP Programming Database 4.25.4, Multilingual
VIN: 2020.06.08
ISTA-P 3.67.1.006 , supports BMW motorcycle and electric vehicle programming.
for BMW ETK 2019.12
for BMW KSD 2019.11
INPA 5.00, winkfp 5.2.3, NCS 3.5.1
BMWAi Refresh Hidden 4.6
E-SYS V3.30 and V3.30, database V67.0, Chinese version software added
DR.GINI B020
The latest FSC navigation code software and IBAC coder
Added DISV57 and DISV44 for old B.M.W cars, diagnostic and programming
Multi-language available in diagnosing, programming and TIS diagram circuit: English, German, Spanish, Russian, Simplified Chinese
New E-Sys feature:
Convert FA to OrderXML file
CR2859 - Encoding 2.0 in E-Sys CR2945 - CVN mapping file in PX container for storing E-Sys functions of CAF
CR2969 - E-Sys - New CAF data model for CAFE-E plug-in coding factory
CR2977 - (E-Sys) FP Certificate Management
CR3008 - New Module TA1 Filter Editor
KA1223 - Use log level mode from properties files in batch
KA1224 - "Restore Defaults" for TAL Processing Parameters
KA2521 - E-Sys: For TAL execution, save the file name and path of the executed TAL log
KA2768 - Expanding TACategory fscBackup from E-Sys KA2807 - Multiple selections and deletions of elements in PDX containers
KA2809 - Multiple vehicle order selection during code verification
KA2825 - Enhanced configuration options for ECUVariantPatterns at E-Sys
KA3009 - Extend the namespace of the PDX container for RSX KA3035 - Rename "Bit6" to "CertEnabled"
K?0941 - Read the output event type of SVTsollK?1002 - TAL processing in VCM in TAL calculation and coding module
K?1071 - Allow multiple selections in event type selection
K?1229 - Service call GetSoftwareID function should be able to do without specifying a diagnostic address
Note that ISTA-P does not support the latest G-system programming, as there is no G-system yet.
Laptop Requirements:
Dual-core processor, better above I3; over 4G of memory
Laptop Recommendation:
It is recommended to use Lenovo ThinkPad: T61, T400, T410, T420, T430, X61, X200, X201, X220 X230 and other laptop with Intel chipset, such as I3 I5 / I7 series.
How to connect BMW ICOM NEXT with vehicles?
Package includes:
ISTA/D— Integrated Service Technical Application Diagnostic. ISTA/D is used to diagnose BMW all series and models from all systems.
ISTA/P— Integrated Service Technical Application/Programming. ISTA/P is used to process all coded, programmed and enable-dependent control modules in BMW Group vehicles.
Rheingold—Diagnostic and repair guide, including Diagrams and disassembly Figure
KSD—BMW KSD (Kaufmännische Service Daten, i.e. Commercial Service Data) is a collection of invaluable data for determining labor hours, inspection sheets and general service methods. There’s also information about wheels and rims for the various models.
EasyConnect— Used to Configure the Environment Parameter of Engineer Software for E series, can activate or release ICOM Port
IToolRadar— Used to recognize ICOM, activate or release ICOM Port
ETK— Accessories Catalog
EDIABAS Tool32— Engineer Software for E series, able to run directly
INPA— Engineer Software for E series, for diagnosis
NCS Expert Tool—- Engineer Software for E series, for coding
WinKFP—Engineer Software for E series, for programming
E-sys — Engineer Software for F series (available for programming and coding)
BMW Standard tool
Coding Database
Coding Tool
V2021.09 BMW ICOM ISTA/D 4.15 ISTA/P 3.65 500G Format HDD
ISTA-D 4.25.4
SDP Programming Database 4.25.4, Multilingual
VIN: 2020.06.08
ISTA-P 3.67.1.006 , supports BMW motorcycle and electric vehicle programming.
for BMW ETK 2019.12
for BMW KSD 2019.11
INPA 5.00, winkfp 5.2.3, NCS 3.5.1
BMWAi Refresh Hidden 4.6
E-SYS V3.30 and V3.30, database V67.0, Chinese version software added
DR.GINI B020
The latest FSC navigation code software and IBAC coder
Added DISV57 and DISV44 for old B.M.W cars, diagnostic and programming
Multi-language available in diagnosing, programming and TIS diagram circuit: English, German, Spanish, Russian, Simplified Chinese
New E-Sys feature:
Convert FA to OrderXML file
CR2859 - Encoding 2.0 in E-Sys CR2945 - CVN mapping file in PX container for storing E-Sys functions of CAF
CR2969 - E-Sys - New CAF data model for CAFE-E plug-in coding factory
CR2977 - (E-Sys) FP Certificate Management
CR3008 - New Module TA1 Filter Editor
KA1223 - Use log level mode from properties files in batch
KA1224 - "Restore Defaults" for TAL Processing Parameters
KA2521 - E-Sys: For TAL execution, save the file name and path of the executed TAL log
KA2768 - Expanding TACategory fscBackup from E-Sys KA2807 - Multiple selections and deletions of elements in PDX containers
KA2809 - Multiple vehicle order selection during code verification
KA2825 - Enhanced configuration options for ECUVariantPatterns at E-Sys
KA3009 - Extend the namespace of the PDX container for RSX KA3035 - Rename "Bit6" to "CertEnabled"
K?0941 - Read the output event type of SVTsollK?1002 - TAL processing in VCM in TAL calculation and coding module
K?1071 - Allow multiple selections in event type selection
K?1229 - Service call GetSoftwareID function should be able to do without specifying a diagnostic address
Note that ISTA-P does not support the latest G-system programming, as there is no G-system yet.
Laptop Requirements:
Dual-core processor, better above I3; over 4G of memory
Laptop Recommendation:
It is recommended to use Lenovo ThinkPad: T61, T400, T410, T420, T430, X61, X200, X201, X220 X230 and other laptop with Intel chipset, such as I3 I5 / I7 series.
How to connect BMW ICOM NEXT with vehicles?
Package includes:
1pc x BMW ICOM NEXT A+B+C
1pc x BMW ICOM B Most
1pc x BMW 20pin Cable
1pc x USB Cable
1pc x LAN Cable
1pc x OBD Cable
1pc x Optical fiber
1pc x 2021.09 BMW ICOM HDD 500G
1pc x BMW ICOM B Most
1pc x BMW 20pin Cable
1pc x USB Cable
1pc x LAN Cable
1pc x OBD Cable
1pc x Optical fiber
1pc x 2021.09 BMW ICOM HDD 500G
