digiprog 3 st59
Cheapest V4.94 Digiprog III Digiprog3 Odometer Master Programmer Entire Kit with ST59 Plug1.Add more car models on the basic of V4.88.2.It is a cost-effective mileage correction tool.3.Supports multi-language and full range of vehicle.4.Comes with ST59 Plug ,Used for NEC Cluster Vehicles
Cheapest V4.94 Digiprog III Digiprog3 Odometer Master Programmer Entire Kit with ST59 Plug is a one of our digiprog 3 st59 Tools, you can buy Cheapest V4.94 Digiprog III Digiprog3 Odometer Master Programmer Entire Kit with ST59 Plug from ukobd2.com.
Wholesale Top quality VAS6154, GM Tech2, VCM II For Ford, Handy Baby II Car Key Chip Copier, CDP DS150
images of Cheapest V4.94 Digiprog III Digiprog3 Odometer Master Programmer Entire Kit with ST59 Plug
Cheapest V4.94 Digiprog III Digiprog3 Odometer Master Programmer Entire Kit with ST59 Plug
V4.94 Digiprog 3 Features:
1. Service interval adjustments and settings
Assyst processing
Fault memory read-erase
EEPROM programmer
Integrated PC communication
Digiprog 3 Menu:
1. EEPROM Menu
The first option on the main menu is the Eeprom menu. Reading, writing and saving Eeprom information is all done using this menu. A more detailed guide to using this menu follows later on in the introduction.
2. CAR/TRUCK Menu
This is the menu you will use for correcting and reprogramming vehicles. Manufacturers are set out in alphabetical order and models of vehicles are set out in a simple sub-menu format.
3. Motorcycle Menu
This menu is the same as the CAR/TRUCK menu but is used for reprogramming motorcycles.
4. Special Functions Menu
The special functions menu is for use only by official DigiProg dealers.
5. Setup Menu
This menu is where settings on your DigiProg can be changed. Language, password, brightness, volume, and the time/date can all be set and changed in this menu. You can also change whether your machine is working in kilometres or miles.
Using the EEPROM Menu:
On some of the vehicles you will come across, an eight pin Eeprom chip will be used to store the vehicle data. These chips hold vital information from the vehicle such as ignition and immobiliser codes. Loss of this information could result in anything from minor faults, to major faults involving the vehicle not starting and having to be taken to the main dealer. This is why it is very important to read and save the original information from the Eeprom before programming, this way if any errors do occur you can always return to the point you started.
The process of reading and saving this information is very simple. The Eeprom chip itself will have a mask number printed across the top of it, for example a widely used chip is a 93C46. You can connect the chip to your DigiProg by using adaptor ST01 or ST04. Most chips are surface mount eeproms which will use ST01, but the larger DIL chips will use ST04.
ST59 Plug for DIGIPROG3 Used for NEC Cluster Vehicles
Compatible with DIGIPROG3 any version.
Installation example: FORD NEC
1. Remove the dashboard and open it . Search on dash the Soldering Points.
2. solder on same points as in picture the cables from ST59 on it. All Pins must be Lift up From Board
3. Connect the Cables to ST59 you can nothing make Wrong
4. Now connect the ST 59 with the Digiprog.
5. Select the program: cars / trucks - FORD - KA NEC.
6. The DIGIPROG denotes old / wrong Mileage.
ST59 Plug for DIGIPROG3 Used for NEC Cluster Vehicles
Compatible with DIGIPROG3 any version.
Installation example: FORD NEC
1. Remove the dashboard and open it . Search on dash the Soldering Points.
2. solder on same points as in picture the cables from ST59 on it. All Pins must be Lift up From Board
3. Connect the Cables to ST59 you can nothing make Wrong
4. Now connect the ST 59 with the Digiprog.
5. Select the program: cars / trucks - FORD - KA NEC.
6. The DIGIPROG denotes old / wrong Mileage.
Package List:
1pc x Digiprog3 Main Unit
1pc x OBD2 Cable
1set x Cables and Adapters
1pc x ST59 Plug
Go to Buy: Cheapest V4.94 Digiprog III Digiprog3 Odometer Master Programmer Entire Kit with ST59 Plug