Menu

Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic

Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic, wholesale Double BTS7960 43A H-bridge High-power Motor Drive, buy Double BTS7960 43A H-bridge High-power Motor Drive from ukobd2.com

UKOBD2 Provide top quality Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic, if you need Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic, or have any questions about Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic, welcome to contact us.

Wholesale Top quality VAS6154, GM Tech2, VCM II For Ford, Porsche Piwis III, USB Link 2, Scania VCI3, CAN Clip, wiTech MicroPod 2, T300 key programmer, locksmith tools

images of Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic

BTS7960B H-bridge 43A high-power motor driver Module Overview:This driver uses chips BTS7960 composed of high-power drive full H-bridge driver module with thermal over-current protection. Double BTS7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43A
Features:
Double BTS7960 large current (43 A) H bridge driver;
5V isolate with MCU, and effectively protect MCU;
5V power indicator on board;
Voltage indication of motor driver output end;
can solder heat sink;PIN
Definition:
1. RPWM: Right Turn PWM
2. LPWM: Left Turn PWM
3. R_EN: Right Turn Enable (High Active)
4. L_EN: Left Turn Enable (High Active)
5. R_IS: Right Turn Current Warning (May Leave Floating)
6. L_IS: Left Turn Current Warning (May Leave Floating)
7. VCC: (5V)
8. GND
Connections:
Method 1:
VCC: 5V from Microcontroller(MCU)
GND: GND from Microcontroller(MCU)
L_PWM: PWM or 5V from Microcontroller(MCU) for CCW(CW) Turns
R_PWM: PWM or 5V from Microcontroller(MCU) for CW(CCW) Turns
R_EN and L_EN: 5V from Microcontroller(MCU)
Method 2:
VCC: 5V from Microcontroller(MCU)
GND: GND from Microcontroller(MCU)
L_PWM: 5V from Microcontroller(MCU) for CCW(CW) Turns
R_PWM: 5V from Microcontroller(MCU) for CW(CCW) Turns
R_EN and L_EN: PWM from Microcontroller(MCU)
Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2);
isolation chip 5V power supply (can share with MCU 5V);
size: 4*5 *1.2cm;
Able to reverse the motor forward, two PWM input frequency up to 25kHZ;
two heat flow passing through an error signal output;
isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply;
the supply voltage 5.5V to 27V;

Go to Buy: Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic

Tags: BTS7960 43A H-bridge High-power Motor Driver module
Prev: 2.4G Remote Control Boat Toy Gift RC Toy Gift Electric 6 Channels Diving Model Wireless Remote Control Submarine Boat Toy
Next: LCR-TC1 1.8" TFT LCD Display Multi-meter Transistor Tester Diode Triode Capacitor Resistor Test Meter MOSFET NPN PNP Triac MOS